Risco-group GT480 Instrukcja Użytkownika

GGGGTTTT444488880000CCCCoooonnnnttttrrrroooollll PPPPaaaannnneeeellllUser InstructionsGardTec 480 User PR5831_11 5IN480UM_B A6 booklet.qxd 19/07/2

PPPPaaaaggggeeee 8888If a MasterCode Reset has been programmed by the engineer, a higher level of code will be required.If Alarm Reset has been pro

PPPPaaaaggggeeee 9999If Antihas been programmed for Alarm Reset, contact the CentralStation or Engineer, (as instructed by the Installation Company

PPPPaaaaggggeeee 11110000Tamper Resetting1) With the display showing:-Enter a valid User code.Then press Yes ( ).2) The exit tone will sound and th

PPPPaaaaggggeeee 111111113) Enter a your User Code again followed by Yes ( ).4) The exit tone will now sound.5) Exit the premises via an authorised

Programming User CodesUp to nine user codes may be programmed on predetermined levels.These are.User Numbers 1 to 3 Master Level.Allows Set, Part Set,

5) Press No ( ).The display will show:-6) Press Yes ( ).The display will show:-7) Press a single digit correspondingto the user number (1 to 9) that y

11) Text is entered in a similar way that you would enter text on a mobile telephone. Select characters from the list below:-1 = ABC 2 = DEF3 = GHI 4

PPPPaaaaggggeeee 11115555Programmable User OptionsSeveral user programmable options are available via user codes 1, 2or 3. To use these options ple

PPPPaaaaggggeeee 111166665) Press 0 twice.The display will show for example:-6) Press Yes ( ) for Full SetorPress 1 for Part 1 SetorPress 2 for Par

PPPPaaaaggggeeee 111177773) Walk around the area being tested. As each device is operated, there will a tone from the internal sounders and the dis

ContentsIntroduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1Display Status Blanking . . . . . . . . . . . . . . . . . .

PPPPaaaaggggeeee 11118888Setting Time & Date1) Enter a valid Master User Code followed by No ( ).The display will show:-2) Press No ( ).The dis

PPPPaaaaggggeeee 111199999) Enter the time using the 24 Hour clock e.g 2300 for 11pm followed by Yes ( ).The display will show, for example:-10) Pr

PPPPaaaaggggeeee 22220000Reading the Log1) Enter a valid Master User Code followed by No ( ).The display will show:-2) Press No ( ).The display wil

PPPPaaaaggggeeee 222211119) To return to the Unset Mode press 0 threetimes.Note:EN control panel only.The the log may store up to 256 events with t

PPPPaaaaggggeeee 22222222System DetailsInstallation By: Address:Tel:Fax:Zone No. Location Type Chime Pt1 Pt212345678Installation Date Service Time

PPPPaaaaggggeeee 22223333Notes:GardTec 480 User PR5831_11 5IN480UM_B A6 booklet.qxd 19/07/2007 17:18 Page 23

PPPPaaaaggggeeee 22224444Notes:GardTec 480 User PR5831_11 5IN480UM_B A6 booklet.qxd 19/07/2007 17:18 Page 24

PPPPaaaaggggeeee 22225555Notes:GardTec 480 User PR5831_11 5IN480UM_B A6 booklet.qxd 19/07/2007 17:18 Page 25

Risco Group UK LtdInternet: www.riscogroup.co.ukRisco Group UK Ltd reserve the right to amend the software and features without prior noticeInstalled

GardTec 480 User PR5831_11 5IN480UM_B A6 booklet.qxd 19/07/2007 17:18 Page 27

IntroductionWelcome to the GT480 control panel. Your installation company willhave programmed your system to protect your premises to the highestpossi

PPPPaaaaggggeeee 2222Display Status BlankingDepending on Control Panel installed, it may be a requirement thatthe Status (Set or Unset display) of

PPPPaaaaggggeeee 3333Full Setting the System.After checking the premises are secure:1) Enter a valid User Code followed by Yes ( ).2) The exit tone

PPPPaaaaggggeeee 4444Pre Exit Check.At the start of the setting procedure, a faulttone will sound if any non exit routes areopen. The display will

PPPPaaaaggggeeee 5555Part Setting the System (using Part 2 or 3).Two other Part Sets may be available for your system. Part 2 is a second set of zo

PPPPaaaaggggeeee 6666Unsetting the System.1) Enter the premises via an authorised Entry Point.2) The entry tone will sound.3) Proceed to the keypad

PPPPaaaaggggeeee 7777Resetting After an AlarmAfter an alarm the system needs to be reset.Your installation company will have programmed the reset m